Sludge Removing Kit 3 in 1

New
Hit
Sludge Removing Kit 3 in 1
Sludge Removing Kit 3 in 1
Sludge Removing Kit 3 in 1

Sludge Removing Kit 3 in 1

One set for complex engine decarbonization from sludge. Effectively cleans the combustion chamber, valves, compression, and oil scraper rings. After cleaning, protects the friction surfaces from further wear. The complex use of decarbonizing foam, decarboil and remetalizing additive increase the efficiency of the cleaning procedure.

Note: 5 cleaning cycles of 5 minutes are more effective than a single application of other foam cleaners.

WHERE TO BUY

Packing: -

Code: 8511

About
Instruction
Where to buy
Three steps to factory cleanliness
Step 1 – RESURS foam carbon cleaner of combustion chamber.

Decarbonization is the process of removing hard-to-dissolve deposits: high-temperature varnish, resins, carbon deposits, which are resistant to traditional flushing.
Unlike liquid decorbanizer, RESURS foam carbon cleaner fills the entire volume of the combustion chamber, cleans nozzles and valves. With five dissolving and rinsing cycles, it works more effectively.


Step 2 – RESURS Decarboil.

This name belongs to an amazing product, which is applied as simply as flushing, and works in strength like Decarbonizing.

Decarboil opens the drainage holes of the piston and restores the mobility of the oil scraper rings
To make the engine clean, as from the factory, it is necessary to repeat the procedure 2-3 times.

Attention: Do not leave RESURS Decarboil with used oil in the engine. After applying Decarboil, it is necessary to drain off the used oil and refill fresh oil. Otherwise, it is possible for the engine parts to stick together due to the high concentration of dissolved resins in the used oil.


Step 3 – RESURS NEXT nano-Concentrate is the most compact engine treatment in the world.

Due to its high efficiency, price and compactness, it has conquered the population in various parts of the world: Nigeria, Mexico and Russia.

After the carbon deposits have been removed, it is necessary to protect the cleaned engine surfaces with metal nanoparticles. The particles use oil as a means of delivery to the friction zones, where, under the influence of temperature and pressure, they block at the micro levels, being embedded in the crystal lattice.

Step № 1

Use foam to clean the intake channels and combustion chamber.

  1. Warm up the engine to operating temperature (40-50 ° С). Remove the coils and spark plugs. Set the pistons in the middle position.
  2. Spray the product in the spark plug hole until it is completely filled with foam.
  3. After the foam settles, let it react with the charcoal deposits for 5-7 minutes. Repeat steps 2 and 3. It’s recommended to repeat the application 5 times.
  4. Pump out the remaining product with a tube or syringe, blow with compressed air.
  5. Cover all spark plug holes with rags to prevent splashing of the liquid.
  6. Turn on the starter for about 10 seconds.
  7. Install all spark plugs and ignition coils.
  8. Start the engine and let it idle for about 5 minutes. Thick smoke may escape from the exhaust pipe. It is necessary to increase the engine speed several times to 3000-4000 rpm, until the smoke becomes less saturated.
  9. It is recommended to repeat the process after 10 thousand km if the engine is heavily contaminated
  10. It is advisable to change the filter and oil. To protect and restore the engine against wear, we recommend applying the RESURS Engine Restorer

Step № 2

  1. Before use, withstand the composition at room temperature for 6 hours.
  2. Check the oil level and choose the correct dosage of the composition. A bottle of 100 ml is designed for 4-5 liters of oil. With a different amount of oil, the dosage is not more than 25 ml per 1 liter of oil.
  3. Warm up the engine to operating temperature, turn it off, open the oil filler.
  4. Pour the recommended dosage into old oil or new oil, flushing oil.
  5. For effective cleaning of highly contaminated engines, it is necessary to keep the engine work in the range of 1700-2300 rpm for 20-25 minutes.
  6. Switch off the engine and allow it to cool, for safely drain of used oil.
  7. After application in engines with a painted oil pan, it is necessary to verify the integrity of the paintwork, if necessary, remove the paint.
  8. Replace filter and oil.

Complex engine decarbonization

Step № 3

Use engine treatment to fill the released surface gaps, reduce friction and increase engine power. It will prevent the further contamination.

1. Warm up the engine.
2. Mix 200 ml of pure oil with the contents of the RESURS Next package. Pour the mixture into the engine oil system.
3. Run engine. The effect will appear after 150 km of run

 

Detailed video instruction

Find nearest distributor in your country: VMPAUTO distributors network.

Our products in web shops

Sergio, your manager at VMPAUTO
Order samples